GLOBEL METAL BIN STORE-6'x3'

The Globel Metal Bin Store is available in 2 sizes - 6'x3', this holds 2x wheelie bins and 8'x3', this holds 3x wheelie bins.  Only one colour is available, Anthracite Grey.  Both sizes come with double front doors and a lift up roof/lid with gas-support struts.  These models also make very good bike stores.

Step 1:

Choose your building size

Select Building Size

Sizes - please note

Our sizes below are nominal and not exact. Please consider the roof overhang before ordering. Exact sizing details can be found under the Technical Specification tab.

 
WIDTH X DEPTH Price
6'x3'
8'x3'

Step 2:

Check to see if we can deliver to you

Step 3:

Customise your building

+ £150
+ £13
+ £85
+ £20
+ £165
+ £30
£345

DIMENSIONS EXPLAINED

x :Overall shed depth including approx 6cm roof overhang

y :Highest point of roof excluding foundation kit or timber floor kit (if ordered) these add 5cm to overall height

z :Eaves height - where the roof starts to slope upwards, excluding foundation kit or timber floor kit (if ordered)

 

Sizes available (width x depth):

6' x 3' 174cm x 101cm X=101cm Y=131cm Z=117cm
8' x 3' 236cm x 101cm X=101cm Y=131cm Z=117cm

N.B. the above measurements are the ROOF measurements; the shed width is approx. 3cm less and the shed depth is 6cm less.

Double doors opening  on both sizes – 136cm high x 120cm wide

Includes lift up roof with gas strut supports

6'x3' holds 2x standard wheelie bins, 8'x3' holds 3x standard wheelie bins

Wall & roof panels – 0.3mm thick hot dipped galvanised steel

Door panels - 0.3mm thick hot dipped galvanised steel

Wall bracing, centre and top rail – 30 x 14mm galvanised steel

Base rail - 30 x 20mm galvanised steel

Ventilated side gables

Foundation kit (optional) – 50mm x 60mm ‘C’ section steel

15 year manufacturer’s warranty

Installation

Choose to have your metal shed installed on to your prepared base

Foundation Kit

Hot dipped galvanised base frame assembles to the exact size of your shed. Assemble and lie onto a firm, compacted, level area and attach shed to frame. This can then be boarded out with plywood or flooded with concrete to provide a level, solid floor.

Hilti Screws and Drill Bit

These fixings secure your shed to a slab base or concreted area. They fit through pre-drilled holes in shed's base rail. Kit supplied with masonry drill bit.

Wooden Floor Kit

Comprises of pressure-impregnated treated tongue & groove boards and bearers. Includes nails for assembly and screws to screw through base rail of the shed into the wooden floor boards. Ideally the floor kit would be assembled on a flat, level slabbed or concreted area.

The website price includes VAT and delivery to all addresses in England & Wales. Delivery is also included to addresses in Scotland within the Glasgow and Edinburgh postcode areas. All other addresses in Scotland carry a delivery surcharge; this is price on application, please phone to discuss. The metal and plastic sheds are delivered flat-packed in a box / boxes. If installation is ordered, the installer usually follows-on after the shed has been delivered.

What is the delivery lead time?

The current lead time is up to 2-3 weeks delivered and an additional week if fitting is required.

What is included in the price?

All prices include VAT and delivery to all areas of mainland England, Wales and Scotland flat packed in a box/boxes. Postcodes in Scotland outside Glasgow and Edinburgh postcodes will be subject to a shipping charge.

What size box does my metal shed come in?

The metal sheds are packed in cardboard boxes and measure approximately 180cm x 80cm x 10cm. The boxes can be quite heavy, larger sheds are packed in two or more boxes. Foundation kits are packaged separately.

Can you provide an installation service?

Yes we can. Prices start from around £200 for smaller metal sheds and increase depending on the size of the shed and if any optional extras are required.

What base do i need for my metal shed?

The ideal base is flat, level slabs or concrete. The shed can be fixed down to this using the Hilti screws or you could use a foundation kit or wooden floor kit (see optional extras). If the Hilti-screws are used to fix the building to your slabs, a mastic sealant is recommended to stop water ingress under the shed walls.

Are the shed dimensions internal or external?

The dimensions given are nominal. For more accurate measurements, please refer to each individual product. The base size (footprint) is given along with the overall size including the roof overhang.

What are the payment terms for metal sheds?

The shed, any accessories and installation need to be paid for in full at time of order.

What guarantee do i get with my building?

A 15 year non-perforation rust guarantee. Door glides and plastic fittings are not covered by the guarantee.

Ways to Buy

 

Buy online

Configure sizes & optional extras
 

Call 0121 707 5066

Speak to our friendly sales team
 

Visit our showroom

Come and see us